Co2 mig welding wire layer winding machine , wire rewinding machine
with Flux cored welding wire / solid welding wire
Co2 mig welding wire rewinding machine
Technical Parameters
1, Suitable for: welding wire and other precision
layer-winding-required metal wire
2, Maximum diameter: Φ2.0mm
3, Minimum diameter: Φ0.8mm
4, Maximum winding speed: 23.0m / s
5, Specification of the wire bobbin:Φ800×600mm (can be customized,
the user should provide the specific drawing)
6, The pay off machine has the function of winding displacement
automatically when reverse the wire.
7, Spool type: D200,D270,D300
8, The maximum weight of each take-up spool: 5kg,15kg,20kg;
9, Wire winding type: Precision layer winding
10, Wire pay off mode: active pay off
11, Brake mode: pneumatic brake
12, Take-up motor specification: 5.5KW, frequency conversion motor
13, The pay off motor specification: 18.5KW, frequency conversion
motor
Note: Φ760 × 500 bobbin required 37.0KW frequency conversion motor
14, The main power supply: 380V,60HZ (three-phase five-wire)
15, The gas source standard: 0.45~0.7Mpa
Product features:
1. Cleverish in shape and convenient to move
2. With a wide range in melting diameter, the steel ropes can be
melted without replacing any parts within the range of prescribed
diameter.
3. Easy to operate, no spanner is needed for tightening device, and
the welding head is nice in apperance
4. Low working power, energy saving and safe in use
our company product scope:
1, Flux cored wire plant project Consulting (including the new
factory process design, old factories technology and equipment
reform, improve the production efficiency, the new product formula
design and development.)
2, Flux cored wire complete line manufacturing
3, Hardfacing & stainless steel etc special flux cored wire product
manufacture
4, Provide high quality 2roll-type and 3roll-type of roller die
cassette for the following types of customers:
flux cored wire manufacturer
solid wire manufacturer
rebar manufacturer
5, Produce various specifications and types of wire drawing
machines used in metal products processing and manufacturing
production equipment parameter
1. Wire material surface pre-treatment
1.1high shelf pay-off:Put a wire rod, without motor
1.2 Scribble and automatic stop switch: wire out
of the pay-off machine through the steel ring with
a diameter of 200 mm, if a few circle wire
entwined, steel ring that was taken to the other
side, t the bottom of the stroke switch will send
signals, and the entire line emergency stop.
1.3 Repeated bending mechanical shell and
wire ball strong scrubbing device: the wire rod
at least six direction perpendicular(National
initiative)Bending heat treatment to strip iron
oxide on the surface of the wire.
Eight peeling wheel, material: ZG45 steel, hardness of HRC50, Wheel
inner diameter Ф 115 --- Ф 120mm.
Wheel service life of 6000 hours. After
peeling ,the wire through period of tapered hole, use wire clean
ball strongly wipe the
surface of wire rod, and does not damage
the wire surface, reduce the waste into the electrolytic pickling
tank, ensure the
effect of pickling, facilitate drawing; By pressure cold water
irrigation and block and
impurities, rust on the surface of the wire rod export
high-pressure gas blowing
device, reduce by wire out of the water.
Special point:
1use seal, integration of the whole machine design, introduction of
foreign top technology, more advanced than similar products in the
country. With high efficiency and low energy consumption, stable
and reliable operation, simple operation and other characteristics.
2, can meet the needs of different specifications of the shape of a
single product, or a combination of size matching diversified
package 3, a power shake out device, to ensure that the packaging
is not damaged 4, a special thermal insulation structure. Can not
only play the role of the best energy-saving, and ensure operator
safety, application of the equipment in welding consumables
industry, with moisture, rust, prolong welding material storage
features 6, adapt to PE, PVC, and other various heat shrinkable
packaging materials.
Take-up system:
№1 Ф800mm I-Spool take-up machine
① Main transmission adopts the transmission efficiency high service
life long V transmitte take form;
②) With pneumatic brake and pneumatic top
device
③ Motor:15 kw variable frequency motor；
④ Ribbon cable with screw thread, maintenance
is simple and practical
⑤ take up by Ф800mm I-spool
⑥ There were equipped with a mechanical locking device, at any
speed, power outages, fly out to ensure that the wheel will not
hurt workers
№2 Ф500mm Trunk-type Unloading Machine
The speed mach with Wire drawing machine.Single layer take-up,The
surface of drum plat WC.Dia of drum is 560mm, take-up plate is
500kg, The machine have:2 take-up plate,2 wheel Barrow.Motor : 15KW
