Automatic Ф 115mm - Ф 120mm 4500*840*1720mm Welded Wire machine for copper
rope and spring industry
Function features-- Automatic Welded wire Mesh Machine
1. This kind of wire mesh welding machine is our latest developed reinforcing mesh welding machine.
2. The line wire and the weft wire of wire mesh welding machine are pre-straight and pre-cut.
3. The line wire is feeding by the servo motor ,pulling the wire net by the servo motor auto.
4. The wire mesh welding machine welding power comes from the cylinders. It’s easy to control the
welding pressure .
5. The weft wire of wire mesh welding machine feeding from the multi hopper which capacity is more over ten
times than the traditional hopper.
6. The new wire mesh welding machine added the bear wire net and carry equipment that makes the working
more convenience .
7. The welding part of wire mesh welding machine is used the springiness input wire trunking that makes the welding
copper use for long time.
8. This wire mesh welding machine adopts synchronous control technique. The cent-control and welding
time are composed of PLC program system. The input front-panel is
touch screen , the operate is more intelligent and reasonable.
Technology parameters
- Overall dimensions (L*W*H) 4500*840*1720(mm)
- Max packing dimension (W*H) 270*100(mm)
- Packing Speed 10-13 sets/min
- Max sealing length 200mm
- Conveyor horizontal hight 800+30(mm)
- Working pressure about 0.5Mpa
- Power source 50Hz/AC380Vthree phase five wire
- Power(Max) about 15kW
Features:
easy operation,low noise,high efficiency
The production process:
№1 Pretreatment, rough production line
Steel wire pretreatment(including:Pay-off stand + Disorderly
parking+New type(water clean)+ Electrolytic pickling + boron
coating + High frequency drying + LZ6/560 straight-line wire
drawing machine + SG800 I-spool take-up machine or none stop
take-up machine
№2 Fine drawing production line
FX800 I-spool(or rotary ) wire pay-off machine + LZ8/400(or
LZ7/400)Straight line wire drawing machine + Tension stand + Wash
tank + SG630I-spool wire take-up machine
№3 Chemical copper plating production line
№4 Layer and packing production line
SG630 spool pay-off machine (active type) + middle + layer winding
machine
№5 S4525 heat shrinkable packaging machine for packaging,
warehousing
Wire Drawing Machine
usage:
this model of wire drawing machine can draw the low carbon,medium
carbon,high carbon wire and the material of wire can be
copper,aluminum,etc.so it is suitable for woodenscrews,electric
lead,copper rope ,spring industry.
production equipment parameter
1. Wire material surface pre-treatment
1.1 high shelf pay-off:Put a wire rod, without motor
1.2 Scribble and automatic stop switch: wire out
of the pay-off machine through the steel ring with
a diameter of 200 mm, if a few circle wire
entwined, steel ring that was taken to the other
side, t the bottom of the stroke switch will send
signals, and the entire line emergency stop.
1.3 Repeated bending mechanical shell and
wire ball strong scrubbing device: the wire rod
at least six direction perpendicular(National
initiative)Bending heat treatment to strip iron
oxide on the surface of the wire.
Eight peeling wheel, material: ZG45 steel, hardness of HRC50, Wheel
inner diameter Ф 115 --- Ф 120mm.
Wheel service life of 6000 hours. After
peeling ,the wire through period of tapered hole, use wire clean
ball strongly wipe the
surface of wire rod, and does not damage
the wire surface, reduce the waste into the electrolytic pickling
tank, ensure the
effect of pickling, facilitate drawing; By pressure cold water
irrigation and block and
impurities, rust on the surface of the wire rod export
high-pressure gas blowing
device, reduce by wire out of the water.
Take-up system:
№1 Ф800mm I-Spool take-up machine
① Main transmission adopts the transmission efficiency high service
life long V transmitte take form;
②) With pneumatic brake and pneumatic top
device
③ Motor:15 kw variable frequency motor；
④ Ribbon cable with screw thread, maintenance
is simple and practical
⑤ take up by Ф800mm I-spool
⑥ There were equipped with a mechanical locking device, at any
speed, power outages, fly out to ensure that the wheel will not
hurt workers
