0.6m - 4m steel bar Reinforcing concrete welded wire mesh machine ,
high efficiency Welding Wire equipment
Welding Wire equipment Specifications:
| max input diameter | 6.5/6.0 | mm |
| min output diameter | 2.2/2.0 | mm |
| rotation speed | 27-168 | r/min |
| each motor power | 15-22 | kw |
| each weight | 1400 | kg |
The Welding Wire equipment process:
- №1 Pretreatment, rough production line
- Steel wire pretreatment(including:Pay-off stand + Disorderly
parking+New type(water clean)+ Electrolytic pickling + boron
coating + High frequency drying + LZ6/560 straight-line wire
drawing machine + SG800 I-spool take-up machine or none stop
take-up machine
- №2 Fine drawing production line
- FX800 I-spool(or rotary ) wire pay-off machine + LZ8/400(or
LZ7/400)Straight line wire drawing machine + Tension stand + Wash
tank + SG630I-spool wire take-up machine
- №3 Chemical copper plating production line
- №4 Layer and packing production line
- SG630 spool pay-off machine (active type) + middle + layer winding
machine
- №5 S4525 heat shrinkable packaging machine for packaging,
warehousing
Our Services
1. Guarantee time: one year since machine was at buyer's factory
but within 18 months against B/L date.
2. Within guarantee time, if any components are broken under normal
condition, we can change for free.
3. We can send our best technician to buyer’s factory for
installation, debugging and training.
4. Complete installation instructions, circuit diagram, manual
operations and machine layout.
5. Timely reply for your machine questions.
6. Main machine packed by stretch film, PLC cabinet packed by air
bubble film, spare parts loaded in to box.
production equipment parameter
1. Wire material surface pre-treatment
1.1 high shelf pay-off: Put a wire rod, without motor
1.2 Scribble and automatic stop switch: wire out
of the pay-off machine through the steel ring with
a diameter of 200 mm, if a few circle wire
entwined, steel ring that was taken to the other
side, t the bottom of the stroke switch will send
signals, and the entire line emergency stop.
1.3 Repeated bending mechanical shell and
wire ball strong scrubbing device: the wire rod
at least six direction perpendicular(National
initiative)Bending heat treatment to strip iron
oxide on the surface of the wire.
Eight peeling wheel, material: ZG45 steel, hardness of HRC50, Wheel
inner diameter Ф 115 --- Ф 120mm.
Wheel service life of 6000 hours. After
peeling ,the wire through period of tapered hole, use wire clean
ball strongly wipe the
surface of wire rod, and does not damage
the wire surface, reduce the waste into the electrolytic pickling
tank, ensure the
effect of pickling, facilitate drawing; By pressure cold water
irrigation and block and
impurities, rust on the surface of the wire rod export
high-pressure gas blowing
device, reduce by wire out of the water.
FAQ
In order to quote the right price, please provide the following
information for the Mesh welding Machine:
1. Wire diameter : From mm to mm.
2. Line wire space : From mm to mm.
Cross wire space : From mm to mm.
3. Mesh width: 1200mm,1500mm, 2000mm, 2500mm, 3000mm ( customized)
4. Industrial voltage : 380V 50HZ ( Customized)
5. Do you want to weld wire mesh panel or mesh in coil ?
6. Is the auxiliary equipment following also require ?
Take-up system:
№1 Ф800mm I-Spool take-up machine
① Main transmission adopts the transmission efficiency high service
life long V transmitte take form;
②) With pneumatic brake and pneumatic top
device
③ Motor:15 kw variable frequency motor；
④ Ribbon cable with screw thread, maintenance
is simple and practical
⑤ take up by Ф800mm I-spool
⑥ There were equipped with a mechanical locking device, at any
speed, power outages, fly out to ensure that the wheel will not
hurt workers
№2 Ф500mm Trunk-type Unloading Machine
The speed mach with Wire drawing machine.Single layer take-up,The
surface of drum plat WC.Dia of drum is 560mm, take-up plate is
500kg, The machine have:2 take-up plate,2 wheel Barrow.Motor : 15KW
Technology parameters
- Overall dimensions (L*W*H) 4500*840*1720(mm)
- Max packing dimension (W*H) 270*100(mm)
- Packing Speed 10-13 sets/min
- Max sealing length 200mm
- Conveyor horizontal hight 800+30(mm)
- Working pressure about 0.5Mpa
- Power source 50Hz/AC380Vthree phase five wire
- Power(Max) about 15kW
